Archive for the Anonymity Category

How to Make a Silencer

Posted in Anonymity, Combat, Improvised Weapons, Survival, Tools with tags , , , , , , , , , , , , , , , , , on April 14, 2008 by jamesshrugged

How to Make a Silencer
Brian Douglas Kendall

Make SilencerA firearm silencer, also known as a suppressor, works in the same way as a car muffler. The muffler consists of chambers for the compression to be dispersed and the sound to be redirected or absorbed. Heat is also reduced throughout the muffler system. A firearm silencer works on the same principle.

There are generally three sections to a firearm silencer:

The first stage of the firearm silencer ususally consists of something that will absorb and dissipate heat rapidly. It also allows for part of the compression to be reduced due to the quick cooling of gases.

The second stage of the firearm silencer usually consists of rubber or plastic washers or discs that help slow down the bullet to sub sonic speeds. It also helps reduce compression.

The third and more complicated stage of the firearm silencer usually consists of tall wooden washers with rubber discs between them or thick chambers of soft plastic. The end of this stage has a low wear rubber cylinder to slow down outgoing air.

The entire firearm silencer is contained within a one and a half inch 300 PSI (Pounds per Square Inch) plastic PVC pipe.

Parts list:

  • 1x 6-14″ 300psi plastic PVC pipe
  • 10-15x Rubber or medium hardness plastic discs
  • 11-16x Soft Wood washers with 1 1/4″ internal diameter
  • 1x Rubber cylinder
  • 5x Rubber discs
  • 6x tall wooden washers, plain
  • 2x steel plugs for the middle and front of the firearm silencer
  • 1x heat and pressure dispersement rod with positioning rings, black.
  • 2x stabilizer donuts to keep the firearm silencer straight, red.
  • 4x separator discs, green.
  • 1x Adapter to attach the firearm silencer to the firearm.

Discs can be cut out with a hole saw, purchased from any local hardware store. The materials can be bought there also. Rubber or plastic can be cut out of tires or trashcans. wooden washers can be cut out of particle board. The steel plugs can be bought at any automotive store as freeze plugs. The heat and pressure rod can be bought at any metal shop; buy at 4-6 inches long Aluminium tube at about 1/8″ thick with an ID (Internal Diameter) as close to the bullet size as possible. Stabilizer donuts can be cut out of birch or oak wood and then drilled with a hole drill. All discs and inserted materials except the head rod should be slightly under 1 1/2″ diameter so that they will fill snugly in the tube.

The heat rod should be drilled full of holes 1/4″ from each end. These holes should be about the same size as the bullet. Leave about a quarter inch gap between each hole. Place a wooden donut at each end and wrap the rod in aluminium screen. Screw the rod into the wood or use epoxy. Place this part into the tube first, this should be very tight and could even have to be hammered into the tube, however do not use screws or glue to hammer it in place.

Now place a steel plug in the tube so that the rounded end is facing the top or exit hole. Now place the adapter in the tube followed by the stabilizer donuts. Make sure the barrel will seat securely in the adapter and that the donuts are snug on the barrel. Make sure you place a separator disc between each stage. Drill little holes in the tube about halfway into the adapter and donuts and place small screws in place to hold them securely.

Note that a small angle is cut into the adaptor to facilitate the sight of the gun. The adaptor has to be reamed at an angle so that the sight will not interfere.

Place a smaller PVC pipe in the front end and push the heat dispersement chamber up to the separator disc, next to the adaptor.

Now from the top, place a wooden washer then plastic disc, washer, disc etc. 9mm ammunition usually requires 12-15 and a 22 usually 6-9. There should be 12-15 discs and 13-16 wooden washers, do not end up with a washer, now place another separator in place.

Last you will need to insert two rubber discs and a tall wooden washer, two discs then a washer. Now place another separator in place. Place the large rubber cylinder in place, this should be about 1/2″ thick. Place the steel plug in place so that the rounded end is facing outwards and rivet it into the front carefully.

Before using be sure there is a clean hole all the way. Use a wooden dowel to see if the firearm silencer is lined up with the barrel hole. All inserted parts should have a hole in the center that is comparable in size to the size of the bullet’s diameter.

Things you should know:

  • Suppressors will slow down the bullet and cause it to defract in another direction.
  • Suppressors do not operate well in cold wheather but this one will for the first few hundred rounds.
  • If you wish to shoot full auto you must double the quantity of internal parts and use an aluminium pipe covered with neoprene sleeve, remember that metal dings.
  • Firearm silencers are illegal in some areas; be safe and know the firearm silencer laws in your location.
Advertisements

Anonymity

Posted in Anonymity, Computer Security with tags , , on November 22, 2007 by jamesshrugged

Here are a few tips on communicating anonymously.

1) Use public resources: Pay phones and Internet Cafe’s. Store items you don’t want to associate with yourself in a public facility; bowling alleys often have places for storage. They normally don’t check for ID, so give a fake name and info.

2) Use pre-paid cell phones, available from $30 from stores like Walmart. These allow you to call without signing anything, no information is provided. Use phone cards, pay with cash.

3) On that note, always pay with cash.

4) Never give identifiable information over the phone or internet. Things like your full name, social security number, address, etc. common sense.

5) when you mail something, do it from a busy drop box, wear gloves when handling anything than has to do with the letter or package. For gods sake, do not lick the stamp.

6) Use anonymous email, from the internet cafe. Hotmail is an obvious choice, since it takes about 3 seconds to set one up and no real personal information is required.

Computer Security

Posted in Anonymity, Computer Security with tags , on November 22, 2007 by jamesshrugged

http://anonymityanywhere.com/index.php?option=com_frontpage&Itemid=1

This program set gives you the ability to browser the internet completely anonymously. This version is CD portable, which means that you can take it with you and use it on any computer that you use. It is based on the very secure proxy system called Tor. Form the site:

http://www.torproject.org/

“Tor is a software project that helps you defend against traffic analysis, a form of network surveillance that threatens personal freedom and privacy, confidential business activities and relationships, and state security. Tor protects you by bouncing your communications around a distributed network of relays run by volunteers all around the world: it prevents somebody watching your Internet connection from learning what sites you visit, and it prevents the sites you visit from learning your physical location. Tor works with many of your existing applications, including web browsers, instant messaging clients, remote login, and other applications based on the Internet’s TCP protocol. ”

Computer security is very important, as it seems that both the US federal government and foreign governments are interested in knowing what you look at on the web.

%d bloggers like this: